Modular DC Power Supply – 62000B
Modular DC Power for burn-in and plating/electrolysis applications. N+1 redundancy, hot-swap maintenance, remote ON/OFF and programmable via the CAN bus.
- Voltage range: 1 ~ 150V
- Current range: Up to 2000A (System)
- Power range up to 1.5KW per module up to 120KW per system
- High Power Density (464 mW / cm3 = 7.13 W/In3)
- N+1 Redundancy
- Ideal for Burn-in & Plating
- Remote Sense
- Remote ON / OFF
- CAN Bus Control
- DC OK Signal Output
Chroma’s new 62000B series of Modular DC Power Supplies offer many unique features for Burn-in and plating/electrolysis applications. The features include a N+1 redundancy, high power densities, hot-swappable maintenance, remote ON/OFF and programmable control via the CAN bus.
Equipped with N+1 redundancy and hot-swap functionality, the 62000B DC Power Supplies are most applicable for 24 hours non-stop applications such as SMD plating production lines, as well as product life burn-in test for IT products like DC converters, LCD backlight inverters and routers.
For continuous operation applications the modular hot-swap design allows engineers to replace the failure unit on-site without shutting down the entire system.
High Power Applications with CSU
The 62000B modular power supplies are capable of providing high power output up to 120KW/2000A with minimal specification degradation via CSU (Control & Supervisor Unit). Each chassis is designed to accommodate a maximum of 9KW and include current sharing capability to ensure system stability. In addition, for convenient control of even large power systems, a CSU is provided to set and display output and protection circuits via a standard CAN bus communication protocol.
A620007 CSU Key Features:
- Stand-alone controller for paralleled 62000B DC power for bulk power
- Digital encoder knobs and function keys
- Simultaneous display of output voltage and current
- Standard Analog programmable interface
- Standard CAN Bus
- Optional Ethernet interface
- User define I/O interface
CAN Bus’s Advantages
Controller Area Network (CAN) is a multicast shared, differential serial bus standard. CAN was specifically designed to be robust in electromagnetically noisy environments and can utilize a differential balanced line like RS-485. It was introduced by Bosch in 1986 for in-vehicle networks in cars and since used in a myriad of applications including factory automation, building automation, aircraft and aerospace as well as in cars, trucks and buses. CAN bus replaced bulky wiring harnesses with a two-wire differential cable. CAN provides services at layers 1 and 2 of the OSI model and uses a broadcast method for placing frames on the wire. CAN provides low-speed, fault-tolerant transmission of 125 Kbps up to 40 meters, which can function over one wire if a short occurs.
Transmission without fault tolerance is provided up to 1 Mbps and 40 meters, and distances up to 1 km are achieved with bit rates of 50 Kbps. Bit rates up to 1 Mbit/s are possible at network lengths below 40m. Decreasing the bit rate allows longer network distances; for example, 125 kbit/s at 500 m.
Control Method For Parallaled
Type A – Control with CSU: User can control via APG, CAN Bus/ Ethernet, and front panel manual control for paralleled operation.
Type B – Control without CSU: User can only control via CAN Bus for paralleled operation.
Note: The SoftPanel can control four mainframes for paralleled operation.
Type C – Control without CSU or PC: User can only control via remote on/off signal for paralleled operation.
|62015B-15-90||DC Power Supply Module, 15V/90A/1350W|
|62015B-30-50||DC Power Supply Module, 30V/50A/1500W|
|62015B-60-25||DC Power Supply Module, 60V/25A/1500W|
|62015B-80-18||DC Power Supply Module, 80V/18A/1440W|
|62015B-150-10||DC Power Supply Module, 150V/10A/1500W|
|62000B-3-1||Three Position 62000B Mainframe|
|62000B-6-1||Six Position 62000B Mainframe|
|A620007||Control & Supervisor Unit|
|G32 325500||Rack mounting kit [62000B-3-1]|
|A620010||Rack Mount Kit [62000B-6-1]|
|A620011||Ethernet Interface [CSU]|
|A620019||USB Control Box [M/F & CSU]|
|A620020||GPIB Interface Control Box [62000B M/F & CSU]|
|A620021||Analog Interface Remote Control Box|
|7028||Dual Channel PC CanBus Card|
|8191||CAN Bus Interface s/Cable [62000B M/F]|
|8217||USB to Canbus Interface|
|G16066900||Filler Panel for Model 62000B Mainframe|
[contact-form-7 id=”4853″ title=”DC Power 62000B”]